高压物理学报

Physical Criterion of Dynamic Tensile Fracture

HE Hong-Liang

2013, 27(2): 153-161. doi: 10.11858/gywlxb.2013.02.001

PDF (433)

Abstract:
A physical criterion of dynamic tensile fracture has been introduced, based on the knowledge of the micro-mechanism and the measurement of the damage evolution. The physical criterion has suggested two critical damage parameters, named as the critical void coalescence damage Dl and the critical fracturing damage Df. These two parameters are associated with a damage function model and a percolation-softening function, by which the fracture process is characterized as that the damage slowly increases in a linear manner from the initial state (D=D0) to the void linkage state (D=Dl), then changes to a nonlinear growth and rapidly approaches to the critical fracturing state (D=Df), while a final step catastrophically leads to the complete fracture state (D=1.0). Experimental measurements and numerical simulations for both of the plate impact and the cylindrical tube have verified that these two parameters (Dl and Df) physically constrain the dynamic tensile fracture and may be considered as the intrinsic material constant. Application of this physical criterion for the prediction of dynamic tensile fracture under intricate loading and for complex geometrical system has been discussed.

Time Dependence of High Pressure Induced Phase Transitions

HONG Shi-Ming

2013, 27(2): 162-167. doi: 10.11858/gywlxb.2013.02.002

PDF (546)

Abstract:
For investigating kinetic behavior of pressure induced phase transitions, it is the most expected to combine high time-resolved diagnostic probes with the precise compression techniques. In fact, an indirect way in large volume press is compare characterization results of recovered samples with their experienced conditions including pressure, temperature and time. As a typical example, relationship between p-T conditions and time for diamond nucleation in C-H-O system is discussed by previous experimental data, demonstrated that extending loading time under HP/HT is propitious to form high pressure stable phase. In contrast, some meta-stable phases, such as bulk amorphous sulfur, metallic glasses and amorphous polymers etc., were obtained by rapid compression process. The results indicated that many substances can show the kinetic features of phase transition in the scale of compression rate from 1 GPa to 1 TPa/s. The kinetic phase diagrams with three dimensions (pressure, temperature and time) could be established through both of the static or rapid compression experiments.

Reviews of Recent Advances of Shock Wave Physics Applied to Earth Science in China

GONG Zi-Zheng, XIE Hong-Sen, FEI Ying-Wei

2013, 27(2): 168-187. doi: 10.11858/gywlxb.2013.02.003

PDF (710)

Abstract:
Academician JING Fu-Qian pioneered two new fields of shock wave physics research in China at the end of the 1980s, that are shock wave physics applied to the Earth science and to the Space science and technology, called go up to the sky and go into the Earth. Academician JING Fu-Qian led us to carry out the only one Major scientific project of high pressure Geosciences－Study on the physical properties under high temperature and high pressure for materials in the important boundaries of the Earth's interior, he also directed the research of hypervelocity impact and protection against space debris impact in China. The recent research advances of shock wave physics applied to the frontier and hot spots of the Earth sciences in China were introduced in great detail and reviewed, including (1) the phase stability, equation of state, sound velocities, and thermo-elasticity of the Earth's lower mantle dominant minerals (Mg,Fe)SiO3 perovskite and MgO-FeO system; (2) the possible mineralogical composition of the lower mantle; (3) the high pressure melting curve of Fe and Fe-O-S system; (4) constrained the light element in the Earth's outer core from the equation of state, sound velocities of Fe-O-S system; (5) the possible mineralogical interpretations of the seismic velocity anomaly in the lower mantle and core-mantle boundary; (6) Near Earth Object impact hazard and defense response. The current problems were emphasized and the new research trends were prospected. The authors dedicated this paper to commemorate the 1st anniversary of Academician JING Fu-Qian passed away.

Structures and Properties in Typical Small-Molecule Crystals under High Pressure

JIN Xi-Lian, CUI Tian

2013, 27(2): 188-198. doi: 10.11858/gywlxb.2013.02.004

PDF (591)

Abstract:
High pressure can cause rearrangement of atoms in microstructure, and arouses reconfigurations of electronic states, which often brings new materials and new properties. The rich and colorful new phenomena and properties in the typical molecule system have been observed under high pressure. Studies of these new phases and behaviors in typical molecular system under high pressure are very important and significative. Two types of substance, i. e. elementary crystals and small-molecule compounds, are investigated thoroughly on structures and properties under high pressure, and demonstrate various features. In the elementary crystals, such as pressure-induced phase transition and metallization in I2 (solid iodine) and N2 (polymeric nitrogen), and in the small-molecule compounds, such as the hydrogen-bond and halogen-bond interactions in crystalline iodoform and bromoform under high pressure, the effects from dihydrogen bonds in ammonia borane which determining the complex dynamics behavior of rotations of the NH3 and BH3 groups under high pressure, etc. are discussed deeply. The distinct behaviors of molecular dissociation, reconstruction of crystal structures, and pressure-induced metallization in the typical small-molecule system under high pressure are very different from the ones at ambient conditions. Exploration of the typical small-molecule crystals under high pressure provides an important way to discover the new structures, new materials and new physical phenomena and properties.

Study on the Thermal Conductivity of HMX Explosive: Method Development and Theoretical Calculation

CHEN Jun, LONG Yao, CHEN Dong-Quan

2013, 27(2): 199-204. doi: 10.11858/gywlxb.2013.02.005

PDF (412)

Abstract:
The theoretical calculation on thermal conductivity of explosive is still one problem. We presented our developed two calculation methods for thermal conductivity of explosive. The first one is based on atomic motion equation. We derived the formulations of thermal flux in system and thermal conductivity of system. It is suitable to calculate the thermal conductivity in different directions. The second one is based on the phonon-phonon dispersion model and Debye model. This method can effectively calculate the thermal conductivity under pressure. Using these two methods, we have calculated the thermal conductivity of HMX under pressure, and deeply analyzed the factors which affect the thermal conductivity of HMX.

Stress Transmission of Materials with Different Strengths under Non-Hydrostatic Compression

RAN Xiang-Tian, HE Duan-Wei, LIU Jing, WANG Qi-Ming, WANG Pei, WANG Jiang-Hua, CHEN Hai-Hua, PENG Fang

2013, 27(2): 205-210. doi: 10.11858/gywlxb.2013.02.006

PDF (416)

Abstract:
Using diamond anvil cell (DAC) combined with synchrotron axial X-ray diffraction (AXRD) techniques, the stress transmission behavior among materials with different strengths was investigated under non-hydrostatic compression. In our experiments, powder mixtures of platinum (Pt) and cubic silicon carbide (-SiC), Pt and tungsten carbide (WC), as well as WC and -SiC, were compressed up to 56, 61, and 25 GPa, respectively. We found that the stress transmission among the grain boundary of two different materials is discontinuous due to their strength difference, and the observed stress difference increases with the strength difference. The stronger material has a smaller observed stress near the minimum stress direction under non-hydrostatic compression in DAC at the same loading.

Molecular Dynamic Simulation on Shock Plasticity Behaviour of Tungsten Alloy

YU Chao, REN Hui-Lan, NING Jian-Guo

2013, 27(2): 211-215. doi: 10.11858/gywlxb.2013.02.007

PDF (462)

Abstract:
The tungsten alloy melting behaviors under high-velocity shock loading is investigated by Molecular Dynamic (MD) method combined with Embedded Atom Method (EAM) potential of tungsten alloy. First, the shock model of tungsten alloy is set up and the numerical simulations of lattice planes (100), (110), (111) under the shock loadings with the same velocity are conducted respectively. The Hugoniot curve and the relative data of pressure, temperature, volume and particle velocity behind the shock wave are obtained. Based on the analyses of the data and the curve, it is found that the shock pressure is in proportion to the shock temperature and inversely proportional to the shock volume. The above conclusions fit to experimental data well when the loading velocity is low, which are extended to the high-velocity impact field. The calculations show the plasticity of tungsten under high-velocity impact in qualitative description.

The 3-D Numerical Simulation for Different Explosive Charges in the Fortifications

REN Hui-Lan, NING Jian-Guo, XU Xiang-Zhao

2013, 27(2): 216-222. doi: 10.11858/gywlxb.2013.02.008

PDF (429)

Abstract:
The basic principle and the parallel design strategy of the PMMIC-3D parallel program which using Euler method based on the message passing interface (MPI) mode were stated. After numerically stimulating the fortification mode, it can be seen that the results of numerical stimulation basically match with the reality and the physical laws. The shock waves of explosive detonation in fortifications not only had a higher peak overpressure, but also had a longer duration of action. When the shock wave met the wall, it would reflect and produce the reflected high pressure. Because of the diffraction convergence, the local high pressure would be brought about in a certain region behind the wall, in which the destructive effect was much larger compared with the shock waves of air explosion. The propagation process and the interaction of shock waves can be seen clearly by the numerical stimulation, which can determine the arrival time of the shock waves at various positions. The optimal explosive charge can be ensured by comparing the overpressure value of shock waves at different places.

The Six over Eight Type Double Stage Large Volume High Pressure and High Temperature Facilities and Their Applications to New Materials Syntheses

LI Xiang, LIU Qing-Qing, FENG Shao-Min, ZHU Jin-Long, CHEN Liang-Chen, JIN Chang-Qing

2013, 27(2): 223-229. doi: 10.11858/gywlxb.2013.02.009

PDF (399)

Abstract:
High-pressure and high-temperature (HPHT) synthesis has play growing importance in exploring new materials. It has the merits of producing many new compounds that otherwise could not be synthesized at ambient conditions. The conventional HPHT facilities are based on so called one stage model reaching pressures up to 10 GPa. It is well understood that the higher synthesis pressure is, the more new compounds will be obtained. Here we introduce a state of the art new type high pressure synthesis facility based on double stage model of the six over eight multi anvils large volume high pressure machine that can reach unprecedented 20 GPa and 2 000 ℃. With the six over eight double stage facilities, much more new high pressure compounds are expected.

Additive Runge-Kutta Methods for Accurate H2-O2-Ar Detonation Simulation

LI Jian, HAO Li, NING Jian-Guo

2013, 27(2): 230-238. doi: 10.11858/gywlxb.2013.02.010

PDF (418)

Abstract:
We report here the additive Runge-Kutta methods for computing reactive Euler equations with a stiff source term, and in particular, their applications in gaseous detonation simulations. The source term in gaseous detonation is stiff due to the presence of wide range of time scales during thermal-chemical non-equilibrium reactive processes and some of these time scales are much smaller than that of hydrodynamic flow. The high order, L-stable, additive Runge-Kutta methods proposed in this paper resolved the stiff source term into the stiff part and non-stiff part, in which the stiff part was solved implicitly while the non-stiff part was handled explicitly. The proposed method was successfully applied to simulate the gaseous detonation in a stoichiometric H2-O2-Ar mixture based on a detailed elementary chemical reaction model comprised of 9 species and 19 elementary reactions. The results showed that the stiffly-accurate additive Runge-Kutta methods can well capture the discontinuity, and accurately describe the detonation complex wave configurations such as the triple wave structure and cellular pattern.

Research Progress on Ultrasonic Velocity Measurement of Liquid Materials under High Pressure

ZHANG Xin, LIU Yong-Gang, SONG Wei, WANG Zhi-Gang, XIE Hong-Sen

2013, 27(2): 239-244. doi: 10.11858/gywlxb.2013.02.011

PDF (430)

Abstract:
The measurement of sound velocity of materials under high temperature and high pressure (HTHP) is an important research content in high pressure science. As a fundamental physical property of liquids, velocity of sound wave in liquids is very important and useful, for many thermodynamic parameters may be derived from sound velocity. However to date, there is little direct experimental information on macroscopic thermodynamic properties of liquids or melts under high pressure, especially the experimental technique to measure sound velocity of liquid has not been well established. The purpose of this paper is to give a brief review on various sound speed measurement techniques of liquid materials under high pressure and a detailed introduction on some new breakthroughs nearly, and finally to point out some expectations in this research field.

Inversion of Constitutive Parameters for Visco-Elastic Materials from Radial Velocity Measurements of Spherical Wave Experiments

LAI Hua-Wei, WANG Zhan-Jiang, YANG Li-Ming, WANG Li-Li

2013, 27(2): 245-252. doi: 10.11858/gywlxb.2013.02.012

PDF (430)

Abstract:
The inversion of visco-elastic constitutive relation from the measured data of a spherical wave experiment is a challenging research. Starting from the governing equations for linear visco-elastic spherical waves which are based on the ZWT visco-elastic constitutive relation, the analytical expression for the attenuation of strong-discontinuous visco-elastic spherical wave front is derived, and consequently a new method is proposed, by which the high-strain-rate visco-elastic parameters could be inversed from a series of particle velocity profiles measured in a spherical wave experiment. The first step is to determine the high-strain-rate elastic module from wave velocity measurements when the quasi-static material parameters are known. Then the high-strain-rate relaxation time can be determined from the attenuation factor. Thus the required visco-elastic constitutive relation can be obtained. Using those material parameters obtained by such a new inversion method, the visco-elastic spherical wave profiles are calculated by the characteristics method. The good agreement between the numerical predictions and the experimental results well supports this proposed new inversion method.

Pressure-Induced Phase Transition of [Emim][PF6] and [Bmim][PF6] Studied by Raman Scattering

ZHU Xiang, WANG Yong-Qiang, WANG Zheng, CHENG Xue-Rui, YUAN Chao-Sheng, CHEN Zhen-Ping, SU Lei

2013, 27(2): 253-260. doi: 10.11858/gywlxb.2013.02.013

PDF (446)

Abstract:
In-situ pressure-induced phase transition of ionic liquids [Emim][PF6] and [Bmim][PF6] have been studied under high pressure and room temperature by using Raman spectroscopy and high-pressure diamond anvil cell (DAC) apparatus. With the increase of pressure, [Emim][PF6] experiences the solid-solid phase transition at about 0.86 GPa, and [Bmim][PF6] experiences the liquid-solid phase transition at about 0.62 GPa and the solid-solid phase transition at about 1.45 GPa. Furthermore, the decrease of pressure of [Bmim][PF6] has also been discussed in details. Pressure-released Raman spectra shows that the phase transition of [Bmim][PF6] is reversible under pressure up to 2 GPa.

High Resolution Numerical Simulation of Compressible Multi-Medium Flow

ZHAO Hai-Tao, WANG Cheng, NING Jian-Guo

2013, 27(2): 261-267. doi: 10.11858/gywlxb.2013.02.014

PDF (486)

Abstract:
We used high resolution 5th-order WENO (Weighted Essentially Non-Oscillatory) scheme, Level Set method and interface treatment method-RGFM (Real Ghost Fluid Method) in simulating compressible multi-medium flow with high density and high pressure ratio. Simulation of one-dimensional gas-water interaction problem was performed, and the accuracy and reliability of the method was verified. This method is applied to two-dimensional deep water and near free surface explosion simulation. From the simulation results of underwater explosion, it indicates that this method can simulate the shock wave generation, propagation, reflection and transmission after interaction with the interface in underwater explosion. This method is strongly advantageous in simulating compressible multi-medium flow with high density ratio, high pressure ratio and strong discontinuity.

Temperature Calibration for the Solid Confining Media Vessel of Large-Size and Thick-Walled Piston-Cylinder Apparatus under High Temperature and Triaxial Pressure

ZHANG Yuan, WAN Zhi-Jun, ZHOU Chang-Bing, LIU Yu

2013, 27(2): 268-276. doi: 10.11858/gywlxb.2013.02.015

PDF (365)

Abstract:
The pressure chamber of 600 ℃ and 20 MN servo-controlled triaxial rock testing system with high temperature and high pressure has adopted the piston-thick-walled cylinder structure. Compared with normal pressure chamber, the inner diameter rises to 300 mm, the outside diameter becomes 1 060 mm and the height grows to 1 100 mm. The size of test specimen also amounts to 200 mm400 mm. The calibration test applies internal heating type and electronic heating approach with low voltage and high current. Before the system is put into use, the reference temperature point should be calibrated. Thus, nine thermocouples were placed in and outside the specimen to observe the temperature variation at these observation points, and to study temperature field characteristics inside of specimen, as well as its relationship with reference point temperature. The calibration experiment results indicate that, the temperature data collected from the middle of the junction of NaCl and micanite paper are stable and reliable, and are in a favorable linear relationship with the inner temperature. Therefore, the place is qualified to be the reference temperature point in the heating process. The test results show that the inner temperatures of the specimen are higher than the temperatures of the junction of NaCl and micanite paper in the same cross section, the middle temperatures of whom are higher than those on both ends. In the inner axial direction, the upper end and the bottom temperature are symmetric to the middle of the specimen whose temperature is higher than either of those of the both ends. The disparity from middle to end grows bigger as the heating temperature increases, the maximum gradient is 0.85 ℃/mm. In the radial direction, the larger distance from the central point, the greater trend of linear temperature distribution. While the central temperature is the lowest, the surface temperature is the highest. The biggest temperature gradient is about 0.5 ℃/mm. The temperature at the central point, 40 mm from the central point, 80 mm from the central point and on the surface of the specimen are respectively larger than the reference temperature by 21%, 27%, 28% and 29%. Whereas, in the inner axial direction, the upper end temperature and the bottom temperature are close, only 1.5% lower than the reference temperature. It is testified that the heating approach is reasonable, and the accuracy of temperature control is high and the temperature of test specimen is well-distributed.

Two and Three Dimensional Numerical Investigations of the Single-Mode Richtmyer-Meshkov Instability

WANG Tao, BAI Jin-Song, LI Ping, TAO Gang, JIANG Yang, ZHONG Min

2013, 27(2): 277-286. doi: 10.11858/gywlxb.2013.02.016

PDF (266)

Abstract:
A high precision numerical algorithm MVPPM (multi-viscous-fluid piecewise parabolic method) is proposed and applied to the multi-viscous-fluid dynamics problems. Several two and three dimensional single-mode Richtmyer-Meshkov instability models with different amplitude and wavelength are numerically simulated by this method. Comparisons show that the evolving of interface is highly sensitive to the initial conditions of perturbation. Both two and three dimensional calculated amplitudes and growth rates of perturbed interface are consistent with the predictions of theoretical models, while the strength of initial perturbation is small. The three dimensional numerical results are identical with the two dimensional ones at the linear stage and larger than the two dimensional ones at the nonlinear stage for the perturbation with the same wavelength and amplitude. Therefore the effects of nonlinearity and three dimensions play a dominant role in the development of Richtmyer-Meshkov instability.

Investigation on the Characteristic Detonation Parameters of C2H2-O2-Ar Mixtures

ZHANG Bo, BAI Chun-Hua

2013, 27(2): 287-291. doi: 10.11858/gywlxb.2013.02.017

PDF (407)

Abstract:
The critical initiation energy and critical tube diameter of C2H2-O2-Ar mixtures were measured in the experiment. The relationship between explosion length, which is theoretical calculated from critical energy, and detonation cell size as well as critical tube diameter was analyzed. The relationship between critical initiation energy and induction zone length was also investigated for each mixture. The results show that, for C2H2-O2 mixtures, a parametric relationship between explosion length and cell size is R0=26, however, this function is changed to R0=37.3 and R0=54.8 when 50% and 70% argon diluted, respectively. The relationship between critical tube diameter and explosion length is R0=2DC. The results indicate that detonation has stable one-dimension ZND structure when argon dilution up to 70%, and a linear relationship is found between critical energy and the cube of induction zone length.

Studies on the Collision of C60O Based on ab Initio Molecular Dynamics Method

LI Jian-Ying, PENG Ru-Fang, LIU Li-Min, JIN Bo, LIANG Hua, LIU Qiang-Qiang, FAN Li-Sheng, CHU Shi-Jin

2013, 27(2): 292-298. doi: 10.11858/gywlxb.2013.02.018

PDF (471)

Abstract:
Recently, an explosive method developed in our group shows promise to prepare He@C60 at high yield. However, the explosive process is rather complex, and much remains unknown about the interaction between fullerenens under this extreme condition. In order to unveil the physical origin of such a process, ab initio molecular dynamics (AIMD) method was used to study the collision of C60O or C60 at high temperature and high pressure by explosion-based method. Many species such as CO@C60 and C59O were generated when the initial speed of collision is 3.28 km/s. By the process of destruction and restoring process of fullerene cage, the endrohendral fullerence can be formed. Such results will be helpful to understand the formation mechanism of endohedral fullerences and to control the formation of fullerene cages by experimental conditions.

Optimization and Analysis of Energy Conversion Efficiency in Single Stage Pulse Induction Coilguns

LIU Wen-Biao, ZHANG Yuan, CAO Yan-Jie

2013, 27(2): 299-304. doi: 10.11858/gywlxb.2013.02.019

PDF (425)

Abstract:
In order to gain the rule between them, the mathematic model of single stage pulse induction coilguns is built, and the launch process is simulated and analyzed. The electrical-to-kinetic energy conversion efficiency of system is regarded as a target function, and the initial position of the armature, the discharge voltage and the capacitance of capacitor banks are regarded as variables. Results of analysis indicate that the time of projectile to be accelerated in the drive-coil should match the time of current rising in the drive-coil. As a rule, the high energy conversion efficiency can be gained in the system with capacitor banks of high voltage and low capacitance.

Experiment and Simulation of Explosion Cloud Diffusion

DUAN Zhong-Shan, LUO Yong-Feng, YUAN Wei, SHANG Ai-Guo

2013, 27(2): 305-312. doi: 10.11858/gywlxb.2013.02.020

PDF (529)

Abstract:
The temporal and spatial distribution of explosion cloud in diffused experiment is analyzed and studied. Cloud diffusion in the atmosphere is simulated by fluid dynamics software. Initial conditions of the cloud are optimized by calculation and experimental program. Cloud movement process rising in vortex flow and flow parameters such as density, velocity, temperature and pressure are obtained from the simulation. The formation mechanism of the explosive mushrooms cloud and the vortex movement in gravity caused by different buoyancy force are discussed and analyzed.

2013 Vol. 27, No. 2

Login in

NewsMore

LinksMore