不同W含量Al/W活性材料的冲击压缩特性

宋超慧; 任会兰; 李尉; 郝莉

doi:10.11858/gywlxb.20210738

不同W含量Al/W活性材料的冲击压缩特性

doi: 10.11858/gywlxb.20210738

宋超慧^1,,
任会兰^1,*, ,,
李尉¹,
郝莉²

1.
北京理工大学爆炸科学与技术国家重点实验室，北京　100081
2.
北京建筑大学理学院，北京　100044

基金项目: 国家自然科学基金（11872124）

详细信息

作者简介:
宋超慧（1996－），男，硕士研究生，主要从事材料动力学性能研究. E-mail：chaohuisong@bit.edu.cn

通讯作者:
任会兰（1973－），女，教授，主要从事多孔材料动力学行为研究. E-mail：huilanren@bit.edu.cn

中图分类号: O347.3; TB333
计量
- 文章访问数: 682
- HTML全文浏览量: 406
- PDF下载量: 32
出版历程
- 收稿日期: 2021-03-09
- 修回日期: 2021-04-02

Impact Compression Characteristics of Al/W Active Materials with Different W Additions

SONG Chaohui^1
,,
REN Huilan^{1,*
, ,},
LI Wei¹,
HAO Li²

1.
State Key Laboratory of Explosion Science and Technology, Beijing Institute of Technology, Beijing 100081, China
2.
School of Science, Beijing University of Civil Engineering and Architecture, Beijing 100044, China

摘要

摘要: 采用模压烧结工艺制备不同W含量的Al/W活性材料，基于分离式霍普金森压杆（SHPB）技术，采用紫铜片和橡胶片进行波形整形，研究不同配比Al/W材料的动态压缩和破坏特性。实验结果表明：随着W含量增多，Al/W材料内部的孔洞、微裂纹逐渐增多；W含量不同，Al/W材料的动态压缩变形和破坏特性呈现明显的差异；W的质量分数为44%和64%时，不同应变率下Al/W的应力-应变曲线呈现出弹性-塑性强化的变形特点，破坏应变随应变率增加而增大； W的质量分数为83%的Al/W材料则表现为塑性阶段的应变软化特点；当W的质量分数达到91%时，Al/W材料达到破坏强度后便迅速失效，破坏应变保持在0.03左右。W含量增加时，Al/W变形模式的转化是增强相W和材料内缺陷相互竞争的结果。
- Al/W活性材料 /
- 波形整形技术 /
- 动态压缩强度
Abstract: In this paper, Al/W active materials with different W additions were prepared by molding and sintering processes. Based on the split Hopkinson pressure bar (SHPB) technology, copper sheets and rubber sheets were used for wave shaping, and dynamic compression and destruction characteristics of Al/W materials with different ratios were evaluated. The experimental results showed that with the increase of W additions, the pores and microcracks inside the Al/W material gradually increased. With different W additions, the dynamic compression deformation and failure characteristics of the Al/W material exhibited obvious differences. When the mass fractions of W are 44% and 64%, the stress-strain curves of Al/W under different strain rates exhibited elastic-plastic strengthening deformation characteristics, and the failure strain increased with the increase of strain rate. Al/W materials with a W mass fraction of 83% exhibited the strain softening characteristic in the plastic deformation stage. When the W mass fraction reached 91%, the Al/W material failed quickly after reaching the breaking strength, and the breaking strain is maintained at about 0.03. With the increase of W additions, the transformation of Al/W deformation mode is the result of the interaction between the reinforcing phase W and the internal defects of the material.
- Al/W active material /
- waveform shaping technology /
- dynamic compression strength

HTML全文

图 1 Al/W试样

Figure 1. Al/W samples

下载: 全尺寸图片幻灯片

图 2 Al/W活性材料的微观形貌

Figure 2. Micrographs of Al/W materials with different W additions

下载: 全尺寸图片幻灯片

图 3 SHPB系统

Figure 3. SHPB system

下载: 全尺寸图片幻灯片

图 4 不同整形器产生的入射波

Figure 4. Incident waves generated by different pulse shapers

下载: 全尺寸图片幻灯片

图 5 紫铜整形器对不同配比的Al/W试件应力均匀性和加载应变率的影响

Figure 5. Effect of copper pulse shapers on the stress uniformity and loading strain rate of specimens with different Al/W ratios

下载: 全尺寸图片幻灯片

图 6 使用橡胶整形器的SHPB实验结果

Figure 6. SHPB experiment results using rubber pulse shaper

下载: 全尺寸图片幻灯片

图 7 Al/W材料的动态真应力-真应变曲线

Figure 7. Dynamic true stress-true strain curves of Al/W materials

下载: 全尺寸图片幻灯片

图 8 SHPB实验后 Al/W 试件的破坏情况

Figure 8. Deformation of Al/W specimens after SHPB tests

下载: 全尺寸图片幻灯片

图 9 不同应变率下Al/W压缩的真应力-应变曲线

Figure 9. Al/W dynamic true stress-strain curves under different strain rates

下载: 全尺寸图片幻灯片

表 1 Al/W试件相关参数

Table 1. Al/W specimen parameters

Test No. Specimen code Mass fraction of W/% Density/(kg·m⁻³) Volume porosity/%

1 AW-44 44 3740 14.5
2 AW-64 64 4950 18.1
3 AW-83 83 6860 27.7
4 AW-91 91 8370 32.9

下载: 导出CSV

表 2 不同配比Al/W试件的动态压缩力学性能

Table 2. Dynamic compression mechanical properties of Al/W with different W additions

Material Strain rate/s⁻¹ Dynamic compression yield strength/MPa

AW-44 1745 137.2
AW-64 1716 168.2
AW-83 1715 187.4
AW-91 1770 157.7 (failure strength)

下载: 导出CSV

参考文献(18)

[1]	National Research Council, Committee on Advanced Energetic Materials and Manufacturing Technologies. Advanced energetic materials [M]. Washington: The National Academies Press, 2004: 20–23.
[2]	DUNBAR E, THADHANI N N, GRAHAM R A. High-pressure shock activation and mixing of nickel-aluminium powder mixtures [J]. Journal of Materials Science, 1993, 28(11): 2903–2914. doi: 10.1007/BF00354693
[3]	OLNEY K L, CHIU P H, LEE C W, et al. Role of material properties and mesostructure on dynamic deformation and shear instability in Al-W granular composites [J]. Journal of Applied Physics, 2011, 110(11): 114908. doi: 10.1063/1.3665644
[4]	CHIU P H, NESTERENKO V F. Dynamic behavior and fracture of granular composite Al-W [C]//DYMAT 2009-9th International Conference on the Mechanical and Physical Behaviour of Materials under Dynamic Loading, 2009: 947–953.
[5]	GUO L F, ZHANG Z M, LI B C, et al. Modeling the constitutive relationship of powder metallurgy Al-W alloy at elevated temperature [J]. Materials & Design, 2014, 64: 667–674. doi: 10.1016/j.matdes.2014.08.031
[6]	HUNT E M, PANTOYA M L. Impact sensitivity of intermetallic nanocomposites: a study on compositional and bulk density [J]. Intermetallics, 2010, 18(8): 1612–1616. doi: 10.1016/j.intermet.2010.04.015
[7]	TUCKER M D. Characterization of impact initiation of aluminum-based intermetallic-forming reactive materials [R]. Atlanta Botanical: Georgia Institute of Technology, 2011.
[8]	SHEMIRANI A B, NAGHDABADI R, ASHRAFI M J. Experimental and numerical study on choosing proper pulse shapers for testing concrete specimens by split Hopkinson pressure bar apparatus [J]. Construction and Building Materials, 2016, 125: 326–336. doi: 10.1016/j.conbuildmat.2016.08.045
[9]	王扬卫, 于晓东, 王璀轶, 等. 准脆性SiC_p/Al复合材料SHPB实验中入射波整形技术 [J]. 北京理工大学学报, 2010, 30(4): 488–491. doi: 10.15918/j.tbit1001-0645.2010.04.004 WANG Y W, YU X D, WANG C Y, et al. Incidence pulse shaping techniques for testing quasi-Brittle SiC_p/Al composites with SHPB [J]. Transactions of Beijing Institute of Technology, 2010, 30(4): 488–491. doi: 10.15918/j.tbit1001-0645.2010.04.004
[10]	SONG Z H, WANG Z H, KIM H, et al. Pulse shaper and dynamic compressive property investigation on ice using a large-sized modified split Hopkinson pressure bar [J]. Latin American Journal of Solids and Structures, 2016, 13(3): 391–406. doi: 10.1590/1679-78252458
[11]	YANG H, SONG H W, ZHANG S. Experimental investigation of the behavior of aramid fiber reinforced polymer confined concrete subjected to high strain-rate compression [J]. Construction and Building Materials, 2015, 95: 143–151. doi: 10.1016/j.conbuildmat.2015.07.084
[12]	CHEN X D, WU S X, ZHOU J K. Experimental and modeling study of dynamic mechanical properties of cement paste, mortar and concrete [J]. Construction and Building Materials, 2013, 47: 419–430. doi: 10.1016/j.conbuildmat.2013.05.063
[13]	FREW D J, FORRESTAL M J, CHEN W. Pulse shaping techniques for testing brittle materials with a split Hopkinson pressure bar [J]. Experimental Mechanics, 2002, 42(1): 93–106. doi: 10.1007/BF02411056
[14]	赵习金, 卢芳云, 王悟, 等. 入射波整形技术的实验和理论研究 [J]. 高压物理学报, 2004, 18(3): 231–236. doi: 10.11858/gywlxb.2004.03.007 ZHAO X J, LU F Y, WANG W, et al. The experimental and theoretical study on the incident pulse shaping technique [J]. Chinese Journal of High Pressure Physics, 2004, 18(3): 231–236. doi: 10.11858/gywlxb.2004.03.007
[15]	ELLWOOD S, GRIFFITHS L J, PARRY D J. Materials testing at high constant strain rates [J]. Journal of Physics E: Scientific Instruments, 1982, 15(3): 280–282. doi: 10.1088/0022-3735/15/3/009
[16]	陶俊林, 田常津, 陈裕泽, 等. SHPB系统试件恒应变率加载实验方法研究 [J]. 爆炸与冲击, 2004, 24(5): 413–418. doi: 10.3321/j.issn:1001-1455.2004.05.006 TAO J L, TIAN C J, CHEN Y Z, et al. Investigation of experimental method to obtain constant strain rate of specimen in SHPB [J]. Explosion and Shock Waves, 2004, 24(5): 413–418. doi: 10.3321/j.issn:1001-1455.2004.05.006
[17]	刘晓俊, 任会兰, 宁建国. 不同配比W/Zr活性材料冲击反应实验研究 [J]. 材料工程, 2017, 45(4): 77–83. doi: 10.11868/j.issn.1001-4381.2016.001212 LIU X J, REN H L, NING J G. Experimental study on impact response of W/Zr reactive materials with different proportions [J]. Journal of Materials Engineering, 2017, 45(4): 77–83. doi: 10.11868/j.issn.1001-4381.2016.001212
[18]	LU Y B, LI Q M. Appraisal of pulse-shaping technique in split Hopkinson pressure bar tests for brittle materials [J]. International Journal of Protective Structures, 2010, 1(3): 363–390. doi: 10.1260/2041-4196.1.3.363