六面顶压机高压腔体温度场的数值模拟

刘芳; 刘永刚; 谢鸿森

doi:10.11858/gywlxb.2012.02.003

六面顶压机高压腔体温度场的数值模拟

doi: 10.11858/gywlxb.2012.02.003

刘芳^1,2,
刘永刚^1, ,,
谢鸿森¹

1.
中国科学院地球化学研究所，贵州贵阳 550002；
2.
中国科学院研究生院，北京 100049

详细信息

通讯作者:
刘永刚 E-mail:liuyg@yahoo.com

计量
- 文章访问数: 7885
- HTML全文浏览量: 415
- PDF下载量: 572
出版历程
- 收稿日期: 2010-09-13
- 修回日期: 2010-12-13
- 发布日期: 2012-04-15

Numerical Simulation of Temperature Field in Sample Assembly of Cubic Press

1.
Institute of Geochemistry, Chinese Academy of Sciences, Guiyang 550002, China;
2.
Graduate University of Chinese Academy of Sciences, Beijing 100049, China

摘要

摘要: 以有限元法为分析手段，在模型和边界条件适当简化的条件下，对六面顶压机高压腔体的温度场进行了数值模拟计算，得出了腔体内的温度分布。在此基础上通过调整模型参数，定性讨论了样品组装设计中组装材料、加热器形状以及导电金属环厚度对温度场的影响。数值模拟结果表明：用氧化锆替代叶蜡石作为堵头和保温材料可以提高样品区的温度，降低功率的消耗并减小样品区的温度梯度；与圆筒形加热器组装相比，中间厚两端薄的变圆筒形加热器组装能提供更高的样品中心温度和较小的温度梯度；使用导电金属环的加热组装时，适当增加金属环的厚度有利于获得较理想的温度分布。研究结果对优化高压实验的样品组装设计、改善温度梯度及保护设备具有一定的参考价值。
- 六面顶压机 /
- 温度场 /
- 样品组装设计 /
- 数值模拟
Abstract: Numerical simulation for the temperature distribution in sample assembly of cubic press was carried out by using the finite-element method with simplified model and boundary conditions. Based on the adjustment of parameters of the models in simulation, the temperature distribution induced by pressure transmission media, shapes of heater and conductive metal ring were discussed in details. The results indicate that the use of zirconia instead of pyrophyllite as the buffer and thermal insulator can elevate the temperature and at the same time lower the thermal gradient in sample area while reducing power consumption. Different shapes of heater will affect on the temperature distribution. In the case of the metal ring being used in assembly, properly increasing the thickness of the ring will be beneficial to obtain desirable temperature distribution. This work could be a useful reference to optimize the design of sample assembly in cubic press for high temperature and high pressure experiments.
- cubic press /
- temperature distribution /
- sample assembly /
- numerical simulation

HTML全文

参考文献(15)

Liu W, Du J G, Yu Y, et al. Correction of temperature gradient in sample cell of pulse transmission experimental setup on multi-anvil high pressure apparatus [J]. Chinese Journal of High Pressure Physics, 2003, 17(2): 95-100. (in Chinese)

刘巍, 杜建国, 于泳, 等. 六面顶压机高温高压弹性波速测量装置样品室温度梯度的校正 [J]. 高压物理学报, 2003, 17(2): 95-100.

Chen X F, He D W, Wang F L, et al. Design and temperature calibration for heater cell of split-sphere high pressure apparatus based on the hinge-type cubic-anvil press [J]. Chinese Journal of High Pressure Physics, 2009, 23(2): 98-104. (in Chinese)

陈晓芳, 贺端威, 王福龙, 等. 基于铰链式六面顶压机的二级6-8模超高压大腔体内置加热元件的设计与温度标定 [J]. 高压物理学报, 2009, 23(2): 98-104.

Watson E B, Wark D A, Price J D, et al. Mapping the thermal structure of solid-media pressure assemblies [J]. Contributions to Mineralogy and Petrology, 2002, 142: 640-652.

Hernlund J, Leinenweber K, Locke D, et al. A Numerical model for steady-state temperature distributions in solid-medium high-pressure cell assemblies [J]. Am Mineral, 2006, 91: 295-305.

Schilling F, Wunder B. Temperature distribution in piston-cylinder assemblies: Numerical simulations and laboratory experiments [J]. Eur J Mineral, 2004, 16: 7-14.

Li R, Ma H A, Han Q G, et al. Analysis of temperature field in diamond synthetic chamber basedon ANSYS [J]. Journal of Jilin University (Engineering and Technology Edition), 2008, 38(3): 535-538. (in Chinese)

李瑞, 马红安, 韩奇钢, 等. 基于ANSYS的金刚石合成腔内的温度场分析 [J]. 吉林大学学报(工学版), 2008, 38(3): 535-538.

Li R, Han Q G, Jia X P, et al. Finite element simulation on distribution of temperature in the HPHT synthesis chamber with sideward heater [J]. Diamond Abrasives Engineering, 2009, 170(2): 9-12. (in Chinese)

李瑞, 韩奇钢, 贾晓鹏, 等. 旁热式高压合成腔体内温场分布的有限元模拟 [J]. 金刚石与磨料模具工程, 2009, 170(2): 9-12.

Feng J F, Lin F, Li L W, et al. Study on temperature of different assembly structure in cubic hinge apparatus [J]. Superhard Material Engineering, 2009, 21(3): 21-25. (in Chinese)

冯吉福, 林峰, 李立惟, 等. 六面顶压机上不同组装结构的温度研究 [J]. 超硬材料工程, 2009, 21(3): 21-25.

Sun Z Q, Xu J A, Xie H S. Computer simulation of the thermal flow inside the high pressure cell (Ⅰ)-Equations and methods of solution [J]. Acta Physica Sinica, 1997, 46(10): 1938-1943. (in Chinese)

孙宗琦, 徐济安, 谢鸿森. 静态超高压大腔体中热流的计算机模拟(Ⅰ)--基本方程和数值求解方法 [J]. 物理学报, 1997, 46(10): 1938-1943.

施引文献

资源附件(0)

访问统计