电磁轨道炮C型固体电枢坡膛段的装填方式研究

张祎; 杨春霞; 栗保明

doi:10.11858/gywlxb.2012.01.007

电磁轨道炮C型固体电枢坡膛段的装填方式研究

doi: 10.11858/gywlxb.2012.01.007

南京理工大学瞬态物理国家重点实验室，江苏南京 210094

详细信息

通讯作者:
栗保明 E-mail:baomingli@vip.sina.com

计量
- 文章访问数: 7756
- HTML全文浏览量: 391
- PDF下载量: 612
出版历程
- 收稿日期: 2011-04-14
- 修回日期: 2011-06-01
- 发布日期: 2012-02-15

Combined Engraving Process of C-Shaped Solid Armature in Electromagnetic Railgun

Science and Technology on Transient Physics Laboratory, Nanjing University of Science and Technology, Nanjing 210094, China

摘要

摘要: 为了满足电磁轨道炮对电枢和轨道间初始接触压力的要求，以小口径电磁轨道炮C型固体电枢的坡膛段装填过程为研究对象，在力学分析的基础上，采用有限元计算方法，对匀速装填、冲击装填以及组合装填3种方式进行了计算，并对电枢臂头部、中间和尾端单元的径向变形、应力和剪切应力随时间的变化进行了对比分析。分析结果表明，在同等条件下，采用组合装填方式可以明显地降低固体电枢在装填过程中受剪切破坏的程度，并有效地提高初始接触压力。研究结果表明，组合装填方式有利于提高电磁轨道炮的发射效率。
- 电枢 /
- 组合 /
- 装填方式 /
- 起始弹道学 /
- 有限元
Abstract: In order to meet the requirement for initial contact pressure between armature and rails of electromagnetic railgun, by taking the engraving process of C-shaped armature in small caliber electromagnetic railgun as the research object, three engraving modes including uniform loading, impact loading and combined loading are simulated by using finite element method based on the mechanical analysis, and then the changes of radial deformation, stress and shear stress of the elements in the armature arm are compared and analyzed. The results show that the combined loading can obviously decrease the degree of shearing damage during solid armature engraving process and, in addition, improve initial contact pressure effectively in the same condition. The research findings show that combined mode is beneficial to increase the launching efficiency of electromagnetic railgun.
- armature /
- combination /
- engraving process /
- initial ballistics /
- finite element

HTML全文

参考文献(14)

Marshall R A, Wang Y. Science and technology of electromagnetic railgun [M]. Translated by Cao Y J. Beijing: Weapon Industry Press, 2006. (in Chinese)

Marshall R A, 王莹. 电磁轨道炮的科学与技术 [M]. 曹延杰, 译. 北京: 兵器科学出版社, 2006.

Watt T, Stefani F, Crawford M, et al. Investigation of damage to solid-armature railguns at startup [J]. IEEE Trans Magn, 2007, 43(1): 214-218.

Stefani F, Parker J V. Experiments to measure wear in aluminum armatures [J]. IEEE Trans Magn, 1999, 35(1): 100-106.

Liu X H, Zhang J G, Zhao Y S. The reservation of contact pressure between C-shaped solid armature and rail [J]. Electrical Engineering, 2010, (Supplement): 8-9. (in Chinese)

刘晓辉, 张建革, 赵彦森. C型固体电枢与导轨接触压力的保持 [J]. 电气技术, 2010, (增): 8-9.

Qiubarov E B. Interior ballistics and engraving force of projectile during engraving [M]. Translated by Yang J R. Beijing: National Defence Industry Press, 1997. (in Chinese)

丘尔巴诺夫. 挤进时期内弹道学与挤进压力计算 [M]. 杨敬荣, 译. 北京: 国防工业出版社, 1997.

Greenwood J A, Williamson J B P. Contact of nominally flat surfaces [J]. Proc Royal Soc Lond, 1966, 295: 300-319.

Moaveni S. Finite element analysis theory and application with ANSYS [M]. Translated by Wang S, Liu L J, Dong C M, et al. 3rd ed. Beijing: Publishing House of Electronics Industry, 2008. (in Chinese)

Moaveni S. 有限元分析--ANSYS理论与应用 [M]. 王崧, 刘丽娟, 董春敏, 等, 译. 第3版. 北京: 电子工业出版社, 2008.

James T E, James D C. Optimum contact region geometry of solid armatures [J]. IEEE Trans Magn, 1997, 33(1): 86-91.

Xiao Z, Chen L X, Xia S G, et al. Geometry design of monolithic C-shaped armature for EML system [J]. High Voltage Engerineering, 2010, 36(7): 1809-1814. (in Chinese)

肖铮, 陈立学, 夏胜国, 等. 电磁发射用一体化C形电枢的结构设计 [J]. 高电压技术, 2010, 36(7): 1809-1814.

施引文献

资源附件(0)

访问统计