A Method for Testing Dynamic Mechanical Behavior of Materials at Ultra-High Temperature and in-Situ Observation
-
摘要: 提出了一种新的超高温(1 600 ℃)动态力学性能测试及原位图像获取方法：在原有分离式Hopkinson压杆的基础上，利用加热源为MoSi2的超高温炉实现超高温环境，采用两个活塞组成双同步系统，利用高速摄像机记录动态变形过程。为了验证所提方法的可行性，以TC4钛合金和SiC陶瓷为研究对象，进行超高温动态力学性能测试，其中：在TC4钛合金实验中，应变率为2 000 s-1，温度范围为20~1 400 ℃，测得其流动应力从1.6 GPa降到150 MPa；在SiC实验中，应变率为250 s-1，温度范围为20~1 200 ℃，测得其压缩强度从250 MPa降到220 MPa。根据高速摄像机记录的试样动态变形过程，分析试样的破坏模式，结果表明：在高温空气环境下，TC4钛合金试样表面有氧化层裂开现象，而在氩气环境下则没有；室温下，SiC试样初始裂纹产生时的应力为压缩强度的80%，而在1 200 ℃下为压缩强度的99%。
-
关键词:
- 超高温 /
- Hopkinson杆 /
- 双同步组装 /
- 高速摄像机
Abstract: In this work, we propose a novel method for testing the dynamic mechanical properties of materials and for in-situ observation at ultra-high temperature (up to 1 600 ℃).The experimental devices used include a classical split Hopkinson pressure bar, a MoSi2 heating source for obtaining ultra-high temperature, two piston rods added to complement the double synchronically assembled system and a high speed camera employed to observe the deformation.To verify the ability of the proposed method for operating at ultra-high temperature, we conducted our experiments on TC4 alloy at temperatures ranging from 20 to 1 400 ℃ and the strain rate of 2 000 s-1, and SiC at temperatures ranging from 20 to 1 200 ℃ and the strain-rate of 250 s-1.The results showed that the peak flow stress of the TC4 alloy specimen drops from 1.6 GPa at room temperature to 150 MPa at 1 400 ℃, and the compressive strength of the SiC specimen drops from 250 MPa at room temperature to 220 MPa at 1 200 ℃.Furthermore, the high speed images revealed that the oxide layer of the TC4 alloy specimen cracked in air but not in argon, and the initial cracks of the SiC specimen occurred at 80% of the compressive strength at room temperature and at 99% of the compressive strength at 1 200 ℃. -
图 1 带有超高速摄像机的超高温双同步SHPB装置示意图
Figure 1. Schematic illustration of the ultra-high temperature SHPB with a double-synchronically assembled heating system and high speed camera
图 2 高速摄像机布局(插图为高温炉内部图像)
Figure 2. High speed camera (The inset shows the internal of the furnace.)
图 3 不同温度下波长与热辐射能量的关系曲线
Figure 3. Wavelength vs.thermal radiation energy at different temperatures
图 4 TC4在应变率为2 000 s-1、温度范围为20~1 400 ℃条件下的应力-应变曲线
Figure 4. Stress-strain curves of TC4 at strain rate of 2 000 s-1 and temperature range of 20 ℃ to 1 400 ℃
图 5 TC4在应变率为2 000 s-1、温度为1 100 ℃、不同气体环境下的应力-应变曲线及形貌
Figure 5. Stress-strain curves and morphologies of TC4 at 2 000 s-1 and 1 100 ℃ in different gas environments
-
[1] 魏延鹏, 虞钢, 段祝平.高温高应变率下异种不锈钢激光焊接件的力学性能[J].爆炸与冲击, 2011, 31(5):504-509. http://www.wanfangdata.com.cn/details/detail.do?_type=perio&id=bzycj201105009WEI Y P, YU G, DUAN Z P.Mechanical properties of laser-welded dissimilar stainless steels structure at elevated temperature and high strain rates[J].Explosion and Shock Waves, 2011, 31(5):504-509. http://www.wanfangdata.com.cn/details/detail.do?_type=perio&id=bzycj201105009 [2] 宫旭辉, 王宇, 夏源明, 等.TC21钛合金的高温动态拉伸力学行为[J].中国有色金属学报, 2010, 20(4):647-654. http://www.ysxbcn.com/down/down_41777.htmlGONG X H, WANG Y, XIA Y M, et al.Dynamic tensile behavior of TC21 titanium alloys at elevated temperatures[J].The Chinese Journal of Nonferrous Metals, 2010, 20(4):647-654. http://www.ysxbcn.com/down/down_41777.html [3] 李玉龙, 郭伟国, 徐绯, 等.Hopkinson压杆技术的推广应用[J].爆炸与冲击, 2006, 26(5):385-394. doi: 10.3321/j.issn:1001-1455.2006.05.001LI Y L, GUO W G, XU F, et al.The extended application of Hopkinson bar technique[J].Explosion and Shock Waves, 2006, 26(5):385-394. doi: 10.3321/j.issn:1001-1455.2006.05.001 [4] CHEN W N, SONG B.Split Hopkinson (Kolsky) bar:design, testing and applications[M].New York:Springer, 2011. [5] 陈荣, 卢芳云, 林玉亮, 等.分离式Hopkinson压杆实验技术研究进展[J].力学进展, 2009, 39(5):576-587. doi: 10.6052/1000-0992-2009-5-J2008-096CHEN R, LU F Y, LIN Y L, et al.A critical review of split Hopkinson pressure bar technique[J].Advances in Mechanics, 2009, 39(5):576-587. doi: 10.6052/1000-0992-2009-5-J2008-096 [6] CHIDDISTER J L, MALVERN L E.Compression-impact testing of aluminum at elevated temperatures[J].Experimental Mechanics, 1963, 3(4):81-90. doi: 10.1007/BF02325890 [7] LINDHOLM U S, YEAKLEY L M.High strain-rate testing:tension and compression[J].Experimental Mechanics, 1968, 8(1):1-9. doi: 10.1007/BF02326244 [8] LATELLA B A, HUMPHRIES S R.Young's modulus of a 2.25Cr-1Mo steel at elevated temperature[J].Scripta Materialia, 2004, 51(7):635-639. doi: 10.1016/j.scriptamat.2004.06.028 [9] LANKFORD J.Temperature-strain rate dependance of compressive strength and damage mechanisms in aluminium oxide[J].Journal of Materials Science, 1981, 16(6):1567-1578. doi: 10.1007/BF02396874 [10] GILAT A, WU X.Elevated temperature testing with the torsional split Hopkinson bar[J].Journal of Materials Science, 1994, 34(2):166-170. doi: 10.1007/BF02325713 [11] NEMAT-NASSER S, ISAACS J B, STARRETT J E.Hopkinson techniques for dynamic recovery experiments[J].Proceedings of the Royal Society A, 1991, 435(1894):371-391. doi: 10.1098/rspa.1991.0150 [12] NEMAT-NASSER S, ISAACS J B.Direct measurement of isothermal flow stress of metals at elevated temperatures and high strain rates with application to Ta and TaW alloys[J].Acta Materialia, 1997, 45(3):907-919. doi: 10.1016/S1359-6454(96)00243-1 [13] SEO S, MIN O, YANG H.Constitutive equation for Ti-6Al-4V at high temperatures measured using the SHPB technique[J].International Journal of Impact Engineering, 2005, 31(6):735-754. doi: 10.1016/j.ijimpeng.2004.04.010 [14] APOSTOL M, VUORISTO T, KUOKKALA V T.High temperature high strain rate testing with a compressive SHPB[J].Journal de Physique Ⅳ (Proceedings), 2003, 110:459-464. doi: 10.1051/jp4:20020736 [15] LI Y, GUO Y, HU H, et al.A critical assessment of high-temperature dynamic mechanical testing of metals[J].International Journal of Impact Engineering, 2009, 36(2):177-184. doi: 10.1016/j.ijimpeng.2008.05.004 [16] 李玉龙, 索涛, 郭伟国, 等.确定材料在高温高应变率下动态性能的Hopkinson杆系统[J].爆炸与冲击, 2005, 25(6):487-492. doi: 10.11883/1001-1455(2005)06-0487-06LI Y L, SUO T, GUO W G, et al.Determination of dynamic behavior of materials at elevated temperatures and high strain rates using Hopkinson bar[J].Explosion and Shock Waves, 2005, 25(6):487-492. doi: 10.11883/1001-1455(2005)06-0487-06 [17] KAJBERG J, SUNDIN K G.Material characterisation using high-temperature split Hopkinson pressure bar[J].Journal of Materials Processing Technology, 2013, 213(4):522-531. doi: 10.1016/j.jmatprotec.2012.11.008 [18] ZHANG C, SUO T, TAN W, et al.An experimental method for determination of dynamic mechanical behavior of materials at high temperatures[J].International Journal of Impact Engineering, 2017, 102:27-35. doi: 10.1016/j.ijimpeng.2016.12.002 [19] SONG B, ANTOUN B R, NIE X, et al.High-rate characterization of 304L stainless steel at elevated temperatures for recrystallization investigation[J].Experimental Mechanics, 2009, 50(4):553-560. doi: 10.1007/s11340-009-9253-6 [20] MATES S P, RHORER R, WHITENTON E, et al.A pulse-heated Kolsky bar technique for measuring the flow stress of metals at high loading and heating rates[J].Experimental Mechanics, 2008, 48(6):799-807. doi: 10.1007/s11340-008-9137-1 -
下载:
点击查看大图
图(7)
计量
- 文章访问数: 7632
- HTML全文浏览量: 3431
- PDF下载量: 319
